Roadcase Hardware

Slam Latch for Slam-Lid System. Easy assembly - Drill or route a finger hole and attach Slam Latch aligned on inside of the lid. To release lid insert finger and disengage the latch and pull the lid off. Part No: L2470

Large Dish with Vertical Louvre. Part No. D0536 Z Material 1.2mm Steel Finish PennBrite Dish Depth 16mm Weight 0.25kg

Dish Punched for 2 x Neutrik D-Series Connectors (XLR, Speakon, RJ45, etc.) Part No. D023K Material 1.2mm Steel Finish Black Dish Depth 16mm Weight 0.25kg

Long Black Plastic Foot Sold individually. Part No. F1699/LD Material Plastic Finish Black Length 35mm Width 12mm Height 8mm Weight 20g

Female PennBrite Zinc Lid Hang This two-piece dish kit is a clever solution for outfitting cases with convenient and unobtrusive hooks to hang a removable lid on when not on the case. This solves the problem of needing to stack many lids in a separate location as well as eliminating the possibility of mixing lids with cases. The H7148-CUP-M and H7148-CUP-F may also be used to couple cases together in a train formation. The hook and hang system lets you train many cases together to roll as one when transporting them across locations. How to use: The lid-fitted H7148-CUP-M is a swing-out handle dish that has a near-flush profile when not in use. The lid can be removed by pulling the handle out, lifting the lid off and then hanging it on the panel-fitted H7148-CUP-F hook dish. Smaller cases may use just one centrally-fitted kit while larger cases can utilise two kits for a double hook. Material Steel Weight 193g Finish Zinc Gender Female

Male PennBrite Zinc Lid Hang This two-piece dish kit is a clever solution for outfitting cases with convenient and unobtrusive hooks to hang a removable lid on when not on the case. This solves the problem of needing to stack many lids in a separate location as well as eliminating the possibility of mixing lids with cases. The H7148-CUP-M and H7148-CUP-F may also be used to couple cases together in a train formation. The hook and hang system lets you train many cases together to roll as one when transporting them across locations. How to use: The lid-fitted H7148-CUP-M is a swing-out handle dish that has a near-flush profile when not in use. The lid can be removed by pulling the handle out, lifting the lid off and then hanging it on the panel-fitted H7148-CUP-F hook dish. Smaller cases may use just one centrally-fitted kit while larger cases can utilise two kits for a double hook. Material Steel Weight 266g Finish Zinc Gender Male

Cover plate for L2455 Small Slam Latch. - An aesthetic finish: once mounted over the slam latch access hole, the cover plate creates a professional and flawless appearance - Save time: thanks to its indent, the plate covers the exposed edges of the access hole, providing a smooth finish without the need to sand Part No. L2455/MBZ Material 1mm Steel Weight 10g

The new R5033X is a door hinge mounted on a 555mm drawer slide that allows you to slide a trap door within a rackmount case when in use. With a simple panel and a slam lock, you can easily create a door that can be hidden within the case when opened. Perfect to build standard 600mm x 600mm shock mount rack cases For use with R8800 Anti-Vibration Rack Systems: the easiest way to build a shock mount rack case. Use crossbar R8800-70 for additional space to fit the sliding door. R50335 - For use with 30mm extrusions. R50338 - For use with 35mm extrusions. Sold in Pairs Extended Load Capacity: 10kg per pair Part No. R50335 & R50338 Material Steel Finish Zinc Description Door Hinge on Drawer Slide

2 Leg Cranked Wrap-Around Corner for Slam-Lid System. Works with Slam Latch L2470, Extrusion E0490-4M and Hook P2472 Part No. C0675/30 Material 1.0mm Steel Finish Zinc Weight 37g

Small Slam Latch for Slam-Lid System. Easy assembly - Drill or route a finger hole and attach Slam Latch aligned on inside of the lid. To release lid insert finger and disengage the latch and pull the lid off. 65% the size of L2470 Use Cover Plate L2455/MBZ for a professional and flawless appearance Can be used with Extrusion E0490, Corner C0675/30 and Hook P2472 Part No. L2455 Description Slam Latch Weight 57g

Sold By The Meter Grip edge 0.7-2.5mm 50m roll, Medium push-on PVC extruded edge trim. Suitable to cover raw edges of fibreglass and metal. With a double lip for better grip. The spring steel core enables a strong grip onto the edge but still provides enough flexibility to go around corners.

Corner Handle 1mm Tight Radius Part No. H2026 Material Steel Finish Zinc or Black Radius 1mm Weight 0.39Kg

Rubber Cable Feedthrough Dish 160mm x 160mm / 6.3" x 6.3" You can pass cabling that is stored inside the case coiled or on a spool through the rubber moulded flaps to hold it in place and prevent it from retreating back inside the case. With this dish, there’s no longer a need to take the cabling out or open the lid to unwind. Simply make the incisions you need along the pre-scored indentations to create one or several openings. Can be used as a single dish or as opposing pairs to create a larger space that can be reached into. Part No. D053510CMZ Finish Zinc Description Recessed Rubber Cable Feedthrough Dish

10A Horizontal Power Dish for Flight Case Built to specifically fit into flight cases, the 10A Flight Case Power Dish (Horizontal) was created for those who require power for additional equipment and access to electricity. The power dish can be used for: - Power distribution for mobile workstations including screen monitors and laptops - Charging battery equipment - Powering up-lighters, LED lighting or other external staging equipment within and outside the case Created to be used in: - Backstage settings - Outdoor settings - Mobile set-ups - Pop-ups and exhibitions The power dishes are easily mounted into any style of flight case, using the same technique as fitting a case handle or dish. There are horizontal (FCH) or vertical (FCV) mounting versions available. The low profile dish gives you the option once fitted, via a PowerCon connector on the front of the dish/case delivering mains power in and through a 10amp thermal breaker to a side loaded IEC chassis socket out situated on the rear of the dish and once fitted situated on the inside of the case. Technical Specifications - PowerCon Input NAC3MPXXA - 10A Thermal Breaker Switch - 10amp IEC Output - Dish Dimensions (OD): 178mm x 127mm x 68mm / 7.01" x 5" x 2.68" - Hole Cutout Dimensions: 148mm x 96mm / 5.83" x 3.78" - Available in two versions: Horizontal & Vertical Part No. PDU10-PCFCH Finish Black Description 10A Horizontal Power Dish Weight 0.6Kg

8mm / 5/16" ex Wrench Actuation Tool for Panel Locks. Use with 9284M Panel Lock. Part No. 9608 Material Steel

Panel lock, Male. Use with 9284F - Sold separately. Mounting style: mortise mount or side mount Use with hex wrench actuation tool 9608 Part No. 9284F Material 1.5mm Steel Description Male Lock style roto-lock Load Rating 700kg Weight 0.23kg

Panel lock, Female. Use with 9284M - Sold separately. Mounting style: mortise mount or side mount Use with hex wrench actuation tool 9608 Part No. 9284F Material 1.5mm Steel Description Female Lock style roto-lock Load Rating 700kg Weight 0.23kg

M3 threaded mounting plate for all D-Series connectors.

Large Rubber Foot with Steel Washer Part No. F1686 Material Black Rubber Finish Black Diameter 40mm Height F1686 - 15.5mm F1686/25 - 25.4mm Weight 26g

Door Trim "h" Extrusion Shipped in 2 meter lengths due to courier limitations. If you need longer lengths please contact us to arrange another freight option. Part No. E2355 Material 6063-T5 Aluminium Panel Thickness 7.2mm Leg Length 27mm Full Length 4m Weight 0.74kg

Door Trim "h" Extrusion Shipped in 2 meter lengths due to courier limitations. If you need longer lengths please contact us to arrange another freight option. Part No. EG-0632 Material 1.5mm Aluminium Panel Thickness 10mm Leg Length 35mm Full Length 4m Weight 1.06kg

Large Latch in Plain Dish. Part No. L925/525S Material 1.2mm Stainless Steel Finish Stainless Steel Description Plain Dish Dish Depth 16mm Weight 0.44kg

Small Non-Marking Tapered Rubber Foot with Steel Washer. Washer Design Helps Eliminate Over-Tightening. Part No. 9120 Material Black Rubber/Steel Finish Black Diameter 21.7mm Height 8.15mm Weight 4g

Electric Flat Screen/Plasma Lift with Remote Control. Include Lid Lifter. 110-240 VAC / 50-60Hz. Mounting Instructions Part No. TS1000 Finish Black Height (Min - Max) 600mm - 1.3m Stroke 700mm Lifting Capacity 65kg

Large Heavy Duty Ball Corner 6 Mounting Holes Internal Radius: 3mm Part No. C1395 Z Material 2mm Steel Finish PennBrite Description Large 2 Leg Ball Corner with Radius Cut-Out Weight 0.2

Catch Plate for L2572 Slam Latch. Part No. L2572-CP Material Steel Finish Penn Brite Description Catch Plate For L2572

Ultra Slim Slam Latch. Works with Extrusion E0490 and Catch Plate L2572-CP Patent Pending Gebrauchsmusterschutz. Registered 20 2014 101 233 Part No. L2572 Description Slam Latch Weight 88g Finish Zinc

Small Briefcase Rubber Foot. Part No. F1694 Material Black Rubber Finish Black Description With Steel Washer Diameter 17.5mm Height 10.2mm Weight 2.2g

Medium MOL Latch in Offset Dish Part No. L978/928SMOL3 Material 1.2mm Steel Description Offset Dish Dish Depth 14mm Offset 22mm Weight 0.22kg

Medium Duty Draw Bolt. Part No. L0956C/NCO Material Steel Finish Chrome Description Draw Bolt Weight 20g

Large Ball Corner. 3 Mounting Holes Part No. C1351Z Material 1.5mm Steel Finish PennBrite Description Large Ball Corner Internal Radius 0.5mm Weight 70g

Medium Ball Corner with 30mm Offset. 3 Mounting Holes. Part No. C1081Z Material 1.2mm Steel Finish PennBrite Description Medium Offset Ball Corner Internal Radius 1mm Weight 49g

Flat Corner, 3 Mounting Holes. Part No. C1935Z Finish PennBrite Material 1.0mm Steel Internal Radius 4mm Description Female Stacking, mates with C1150 Stackable Female Weight 40g

Triangular Corner. Part No. C0679 Finish PennBrite Material 1.2mm Steel Internal Radius 4.1mm Weight 51g

Large Butterfly Catch, Padlocking. Catch plate included. Part No. L0935 Material Steel Finish PennBrite Weight 31g

Brace Ball Corner, 30mm Offset on one leg only (for use in lidmaker applications). For use with Extrusion E0870 or other Female Stacking Corner. 3 Mounting Holes Part No. C1082/01 Material 1.2mm Steel Finish PennBrite Description Offset Brace Ball Corner Internal Radius 0.8mm Offset 30mm Stackable Female Weight 46g